.svg){kind=small}
MFP Nano Plus 4000 system
MFP Nano plus 4000 with U-SMPS – Real-time determination of fraction separation efficiency in accordance to DIN EN 1822-3 / ISO 29463-3 with two UF-CPC in raw and clean gas and detection of MMPS range
MFP Nano Plus 4000 system
- Real-time determination of the fraction separation efficiency above 10 nm
- The measuring time for determining the fraction separation efficiency is halved by measuring the particle concentration in the raw and clean gas.
- No dilution necessary!
- Combining two UF-CPC versions, the UF-CPC for the highest concentrations up to 2,000,000 particles/cm3 (single count mode) in the raw gas and the UF-CPC 50 for top counting rates at low concentrations in the clean gas, corresponds to a dilution factor of 1:200.
- Internationally comparable measurement results in accordance with DIN EN 1822-3 and ISO 29463-3
- Simple use of different test aerosols, such as NaCl / KCl or DEHS (others on request)
- Simple measurement of the fraction separation efficiency and determination of the MPPS range
- High reproducibility of the testing method
- Flexible filter test rig software FTControl
- Easy to operate, even untrained personnel can be quickly trained in the use of the equipment
- Cleaning can be performed independently by the customer
- Short set-up times
- Portable installation, easy to move thanks to the integrated wheels on the MFP Nano Plus 4000 system
- Clear verification of the function of the individual components and the system as a whole in the scope of pre-delivery acceptance testing and at delivery
- Reliable function
*Learn more about Palas: Here
*Fanpage: DIGI TECHNOLOGIES
Technical Data |
Description |
| Measurement range (size) | U-SMPS: 10 – 800 nm |
| Volume flow | 0.48 – 5.76 m³/h (pressurized operation) |
| Power supply | 115/230 V; 50/60 Hz |
| Dimensions | Approx. 760 • 2,100 • 985 mm (W • H • D) |
| Inflow velocity | 1.3 – 16 cm/s (others on request) |
| Differential pressure measurement | 0 – 2,500 Pa (others on request) |
| Test area of the medium | 100 cm² |
| Aerosol | Dusts (e. g. SAE dusts), salts (e. g. NaCl, KCl), liquid aerosols (e. g. DEHS) |
| Compressed air supply | 6 – 8 bar |
- Prüfung von Filtermedien und kleinen Minifiltern in der Produktentwicklung und bei der Produktionsüberwachung
- Prüfmöglichkeit nach DIN EN 1822-3 (HEPA / ULPA) und ISO 29463-3
- Fraktionsabscheidegradmessung für andere Filtermedien im Bereich von ca. 20 nm bis 1 μm
Related Products
Dilution system – PMPD 1000
Dilution system ejector for the PMP application with dilution factor 1:1000. The PMPD 1000 dilution system is a dilution system according to the ejector principle that was especially developed for the PMP application or the PMP measurement chain. The PMPD 1000 achieves a dilution factor of 1:1000 by means of a thermodiluter up to 200°C.
Dilution system – PMPD 100
Dilution system ejector for the PMP application with dilution factor 1:100 The PMPD 100 dilution system is a dilution system according to the ejector principle that was especially developed for the PMP application or the PMP measurement chain. The PMPD 100 achieves a dilution factor of 1:000 by means of a thermodiluter up to 200°C.
Dilution systems – DC 10000
The DC 10000 consists of four cascaded special dilution systems with the dilution factor 1:10. The DC 10000 dilution cascade has one aerosol inlet and four aerosol outlets. Depending on which aerosol outlet is connected to the measuring device, the aerosol with the dilution factors 1:10, 1:100, 1:1,000 or 1:10,000 are diluted and measured.
Dilution system – KHG 10
KHG 10 D dilution system heatable and pressure-resistant up to 10 bar for isothermal and isobaric dilution with a dilution factor of 1:10.
Dilution system – VKL 100
Dilution system with dilution factor 1:100 The Palas® VKL 100 dilution systems are used in vertical operation for the particle size range up to 2 µm for applications in the clean room. Dilution factors of up to 1:100,000 are achieved by cascading several VKL systems.
Dilution system – VKL 10
The VKL 10 series of dilution systems can reduce the concentration of aerosols by the dilution factor 01:10, also of very highly concentrated aerosols, in a defined and reliable way. The Palas® VKL 10 dilution systems are used in vertical operation for the particle size range up to 20 µm for powders and dusts. Dilution factors of up to 1:100,000 are achieved by cascading several VKL systems.
Dilution system – LDD 100
The dilution of large droplets is particularly important when measuring highly concentrated droplet aerosols. Since large droplets are difficult to dilute, standard systems only work up to a size of 1 – 2 μm. The newly developed dilution system LDD 10 (dilution factor 10) is the first system to dilute almost loss-free large droplets up to 10 μm.
Dilution system LDD 10
The dilution of large droplets is particularly important when measuring highly concentrated droplet aerosols. Since large droplets are difficult to dilute, standard systems only work up to a size of 1 – 2 μm. The newly developed dilution system LDD 10 (dilution factor 10) is the first system to dilute almost loss-free large droplets up to 10 μm.
LSPG 16890 system
Aerosol generator for KCl and other salt particles up to 10 μm based on ISO 16890
AGK 2000
Generation of solid particles out of suspensions, solutions and biological agents Solid particle aerosols produced from suspensions, e.g. with biological agents, and solutions such as NaCl and KCl, are required for numerous applications in research, development and quality assurance.
DNP Digital 3000
Generation of nano-scale test aerosols from graphite, silver (Ag), gold (Au), copper (Cu), etc. through condensation; Carrier gas: Nitrogen or Argon (Replacement product of the GFG 1000)
BEG 3000
Test aerosols from powder, dust, pollen, etc.; mass flow approx. 8 g/h – 7.3 kg/h; with automatic mass flow monitoring and refill unit
