.svg){kind=small}
Hệ thống kiểm tra bộ lọc – DFP 3000
Compressed air filter testing system newly developed DFP 3000 provides fully automated measurements of fractionation efficiency for compressed air filters under overpressure up to 7 bar, providing better in-process results than ISO 12500.
DFP 3000 system:
- Các phép đo hạt bụi nhanh chóng
- Kết quả phép đo có thể so sánh trên toàn thế giới
- High reproducibility of the testing method
- Dễ dàng sử dụng các aerosol kiểm tra khác nhau, ví dụ: DEHS, bụi SAE
- Flexible filter test rig software FTControl
- Trình tự các chương trình được lên linh hoạt cho các phép đo tổn thất áp suất, hiệu quả phân tách từng phần và các phép đo tải
- Trình tự kiểm tra hoàn toàn tự động, có thể tái lập bao gồm kiểm soát áp suất và lưu lượng thể tích
- Dễ dàng vận hành, thậm chí người chưa được đào tạo cũng có thể được hướng dẫn sử dụng nhanh chóng
- Short set-up times
- Làm sạch và hiệu chuẩn có thể được thực hiện độc lập bởi khách hàng
- Cài đặt linh động, dễ dàng di chuyển nhờ bánh xe
- Reliable operation
- Xác định chức năng rõ ràng của mỗi thành phần – thậm chí trong các ứng dụng khác
- Low maintenance costs with the DFP 3000 . compressed air filter test system
*Learn more about Palas: Here
*Fanpage: DIGI TECHNOLOGIES
Technical Data |
Description |
| Volume flow | 1 to 60 Nm³/h
or 10 to 200 Nm³/h |
| Power supply | 115/230 V; 50/60 Hz |
| Dimensions | 300 x 130 x 60 cm (W x H x D) |
| Differential pressure measurement | 0 to 3000 Pa |
| Aerosol | liquid Aerosol, example: DEHS |
| Aerosol concentrations | up to 10^6 particals/cm³ |
| Compressed air supply | 10 barg |
| Pressure | 1 to 7 barg relative |
| Measurement range (size) | 0,2 to 40 µm,
0,3 to 40 µm at 7 barg |
- Comprehensive filter testing better than ISO 12500
- Check filter media
- Determine the amount of drainage during loading
Related Products
Dilution system – PMPD 1000
Dilution system ejector for the PMP application with dilution factor 1:1000. The PMPD 1000 dilution system is a dilution system according to the ejector principle that was especially developed for the PMP application or the PMP measurement chain. The PMPD 1000 achieves a dilution factor of 1:1000 by means of a thermodiluter up to 200°C.
Dilution system – PMPD 100
Dilution system ejector for the PMP application with dilution factor 1:100 The PMPD 100 dilution system is a dilution system according to the ejector principle that was especially developed for the PMP application or the PMP measurement chain. The PMPD 100 achieves a dilution factor of 1:000 by means of a thermodiluter up to 200°C.
Dilution systems – DC 10000
The DC 10000 consists of four cascaded special dilution systems with the dilution factor 1:10. The DC 10000 dilution cascade has one aerosol inlet and four aerosol outlets. Depending on which aerosol outlet is connected to the measuring device, the aerosol with the dilution factors 1:10, 1:100, 1:1,000 or 1:10,000 are diluted and measured.
Dilution system – KHG 10
KHG 10 D dilution system heatable and pressure-resistant up to 10 bar for isothermal and isobaric dilution with a dilution factor of 1:10.
Dilution system – VKL 100
Dilution system with dilution factor 1:100 The Palas® VKL 100 dilution systems are used in vertical operation for the particle size range up to 2 µm for applications in the clean room. Dilution factors of up to 1:100,000 are achieved by cascading several VKL systems.
Dilution system – VKL 10
The VKL 10 series of dilution systems can reduce the concentration of aerosols by the dilution factor 01:10, also of very highly concentrated aerosols, in a defined and reliable way. The Palas® VKL 10 dilution systems are used in vertical operation for the particle size range up to 20 µm for powders and dusts. Dilution factors of up to 1:100,000 are achieved by cascading several VKL systems.
Dilution system – LDD 100
The dilution of large droplets is particularly important when measuring highly concentrated droplet aerosols. Since large droplets are difficult to dilute, standard systems only work up to a size of 1 – 2 μm. The newly developed dilution system LDD 10 (dilution factor 10) is the first system to dilute almost loss-free large droplets up to 10 μm.
Dilution system LDD 10
The dilution of large droplets is particularly important when measuring highly concentrated droplet aerosols. Since large droplets are difficult to dilute, standard systems only work up to a size of 1 – 2 μm. The newly developed dilution system LDD 10 (dilution factor 10) is the first system to dilute almost loss-free large droplets up to 10 μm.
LSPG 16890 system
Aerosol generator for KCl and other salt particles up to 10 μm based on ISO 16890
AGK 2000
Generation of solid particles out of suspensions, solutions and biological agents Solid particle aerosols produced from suspensions, e.g. with biological agents, and solutions such as NaCl and KCl, are required for numerous applications in research, development and quality assurance.
DNP Digital 3000
Generation of nano-scale test aerosols from graphite, silver (Ag), gold (Au), copper (Cu), etc. through condensation; Carrier gas: Nitrogen or Argon (Replacement product of the GFG 1000)
BEG 3000
Test aerosols from powder, dust, pollen, etc.; mass flow approx. 8 g/h – 7.3 kg/h; with automatic mass flow monitoring and refill unit
